2006年4月 6日

[vine-users:074376] Re: ADSL(フレッツ)で接続できません。

上妻 久仁和です。

書き忘れていたのですが、使っているのは、
Vine Linux 3.2 です。

/etc/sysconfig/network-scripts/ifcfg-eth0
の ONBOOT=yes と ONBOOT=no の場合の dmesg を
載せておきます。


ONBOOT=yes の場合

map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 3192.1555 MHz.
..... host bus clock speed is 199.5097 MHz.
cpu: 0, clocks: 1995097, slice: 665032
CPU0
cpu: 1, clocks: 1995097, slice: 665032
CPU1
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xfd885, last bus=10
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
PCI: Unable to handle 64-bit address for device 02:00.0
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 11 14 15) *4
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *10 11 14 15)
PCI: Probing PCI hardware
00:00:01[A] -> 2-16 -> IRQ 16 level low
00:00:1c[A] -> 2-17 -> IRQ 17 level low
00:00:1c[C] -> 2-18 -> IRQ 18 level low
00:00:1c[D] -> 2-19 -> IRQ 19 level low
00:00:1d[A] -> 2-23 -> IRQ 23 level low
00:00:1e[B] -> 2-20 -> IRQ 20 level low
00:0a:03[B] -> 2-21 -> IRQ 21 level low
00:0a:03[C] -> 2-22 -> IRQ 22 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02008000
....... : physical APIC id: 02
....... : Delivery Type: 1
....... : LTS : 0
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 1 0 0 0 1 1 71
0a 003 03 0 0 0 0 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 003 03 1 1 0 1 0 1 1 A9
11 003 03 1 1 0 1 0 1 1 B1
12 003 03 1 1 0 1 0 1 1 B9
13 003 03 1 1 0 1 0 1 1 C1
14 003 03 1 1 0 1 0 1 1 D1
15 003 03 1 1 0 1 0 1 1 D9
16 003 03 1 1 0 1 0 1 1 E1
17 003 03 1 1 0 1 0 1 1 C9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: Failed to allocate resource 0(4f800000-0) for 02:00.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
ACPI: Power Button (FF) [PWRF]
vesafb: framebuffer at 0xc0000000, mapped to 0xe001d000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at a5f3:1f5f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.1 (2004-01-29) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 00:1f.1
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3c40-0x3c47, BIOS settings: hda:DMA, hdb:pio
hda: MATSHITADVD-RAM SW-9585S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 182k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
libata version 1.11 loaded.
ata_piix version 1.03
PCI: Setting latency timer of device 00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x3C90 ctl 0x3C86 bmdma 0x3C50 irq 19
ata2: SATA max UDMA/133 cmd 0x3C88 ctl 0x3C82 bmdma 0x3C58 irq 19
ATA: abnormal status 0x7F on port 0x3C97
ata1: disabling port
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3f01 87:4003
88:203f
ata2: dev 0 ATA, max UDMA/100, 586072368 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi0 : ata_piix
scsi1 : ata_piix
Vendor: ATA Model: WDC WD3000JD-55K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 164k freed
Real Time Clock Driver v1.10f
Adding Swap: 1012052k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,8), internal journal
Intel 810 + AC97 Audio, version 1.01, 03:27:47 Sep 5 2005
PCI: Setting latency timer of device 00:1e.2 to 64
i810: Intel ICH4 found at IO 0x3880 and 0x3000, MEM 0xb0040800 and
0xb0040400, IRQ 17
i810: Intel ICH4 mmio at 0xe02ae800 and 0xe02b0400
i810_audio: Primary codec has ID 2
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 2
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not
present), total channels = 2
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb-uhci.c: $Revision: 1.275 $ time 03:28:47 Sep 5 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 23
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x38c0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x38e0, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0x3c00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: PCI device 8086:265c (Intel Corp.)
ehci_hcd 00:1d.7: irq 23, pci mem e0314000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: USB disconnect on device 00:1d.0-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: connect-debounce failed, port 1 disabled
hub.c: cannot disable port 1 of hub 1 (err = -19)
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: get_hub_status failed
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: get_hub_status failed
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 00:1d.1-0 address 1
usb.c: USB bus 2 deregistered
usb.c: USB disconnect on device 00:1d.2-0 address 1
usb.c: USB bus 3 deregistered
usb.c: USB disconnect on device 00:1d.3-0 address 1
usb.c: USB bus 4 deregistered
ehci_hcd 00:1d.7: remove state 3
usb.c: USB disconnect on device 00:1d.7-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: connect-debounce failed, port 1 disabled
hub.c: cannot disable port 1 of hub 1 (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: get_hub_status failed
usb.c: USB bus 5 deregistered
ohci1394: $Rev: 1045 $ Ben Collins
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[b0201000-b02017ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
ieee1394: Node removed: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
usb-uhci.c: $Revision: 1.275 $ time 03:28:47 Sep 5 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 23
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x38c0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x38e0, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0x3c00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: PCI device 8086:265c (Intel Corp.)
ehci_hcd 00:1d.7: irq 23, pci mem e0314000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
hid-core.c: USB HID support drivers
ohci1394: $Rev: 1045 $ Ben Collins
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[b0201000-b02017ff] Max
Packet=[2048]
Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension
(NICE) ver. 8.3.14 (11/2/05)
PCI: Setting latency timer of device 02:00.0 to 64
bcm5700 : Unknown NVRAM type.
VPD read failed
eth0: Broadcom BCM5751 1000Base-T PCI Express found at mem 4f800000, IRQ
16, node addr 000ae47ec497
eth0: Broadcom BCM5750 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
802.1Q VLAN ON, NAPI ON
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
hub.c: connect-debounce failed, port 1 disabled
eth0: Using PCI INTX interrupt
hub.c: new USB device 00:1d.3-2, assigned address 2
input: USB HID v1.10 Device [Fujitsu Remote Control Receiver] on usb4:2.0
hub.c: new USB device 00:1d.0-1, assigned address 2
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb1:2.0
usb.c: registered new driver usbmouse
input: USB HID v1.10 Device [Fujitsu Remote Control Receiver] on usb4:2.1
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
hub.c: new USB device 00:1d.0-2, assigned address 3
hub.c: USB hub found
hub.c: 3 ports detected
apm: BIOS not found.
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
hub.c: new USB device 00:1d.0-2.1, assigned address 4
Yenta ISA IRQ mask 0x04b8, PCI irq 23
Socket status: 30000006
input: USB HID v1.00 Keyboard [Chicony PFU-65 USB Keyboard] on usb1:4.0
Yenta ISA IRQ mask 0x04b8, PCI irq 20
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
lp: driver loaded but no devices found
bcm5700: eth0 NIC Link is DOWN
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 430M
agpgart: Detected an Intel(R) 915G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
cdrom: This disc doesn't have any tracks I recognize!
bcm5700: eth0 NIC Link is DOWN
eth0: Using PCI INTX interrupt
bcm5700: eth0 NIC Link is DOWN
bcm5700: eth0 NIC Link is DOWN
eth0: Using PCI INTX interrupt
bcm5700: eth0 NIC Link is DOWN

ONBOOT=no の場合

BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: Physical Processor ID: 0
CPU: After generic, caps: bfebfbff 20100000 00000000 00000000
CPU: Common caps: bfebfbff 20100000 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 03
Total of 2 processors activated (12753.30 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 3192.0031 MHz.
..... host bus clock speed is 199.5000 MHz.
cpu: 0, clocks: 1995000, slice: 665000
CPU0
cpu: 1, clocks: 1995000, slice: 665000
CPU1
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xfd885, last bus=10
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S3 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
PCI: Unable to handle 64-bit address for device 02:00.0
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 11 14 15) *4
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *10 11 14 15)
PCI: Probing PCI hardware
00:00:01[A] -> 2-16 -> IRQ 16 level low
00:00:1c[A] -> 2-17 -> IRQ 17 level low
00:00:1c[C] -> 2-18 -> IRQ 18 level low
00:00:1c[D] -> 2-19 -> IRQ 19 level low
00:00:1d[A] -> 2-23 -> IRQ 23 level low
00:00:1e[B] -> 2-20 -> IRQ 20 level low
00:0a:03[B] -> 2-21 -> IRQ 21 level low
00:0a:03[C] -> 2-22 -> IRQ 22 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02008000
....... : physical APIC id: 02
....... : Delivery Type: 1
....... : LTS : 0
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 1 0 0 0 1 1 71
0a 003 03 0 0 0 0 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 003 03 1 1 0 1 0 1 1 A9
11 003 03 1 1 0 1 0 1 1 B1
12 003 03 1 1 0 1 0 1 1 B9
13 003 03 1 1 0 1 0 1 1 C1
14 003 03 1 1 0 1 0 1 1 D1
15 003 03 1 1 0 1 0 1 1 D9
16 003 03 1 1 0 1 0 1 1 E1
17 003 03 1 1 0 1 0 1 1 C9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: Failed to allocate resource 0(4f800000-0) for 02:00.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
ACPI: Power Button (FF) [PWRF]
vesafb: framebuffer at 0xc0000000, mapped to 0xe001d000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at a5f3:1f5f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.1 (2004-01-29) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 00:1f.1
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3c40-0x3c47, BIOS settings: hda:DMA, hdb:pio
hda: MATSHITADVD-RAM SW-9585S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 182k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
libata version 1.11 loaded.
ata_piix version 1.03
PCI: Setting latency timer of device 00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x3C90 ctl 0x3C86 bmdma 0x3C50 irq 19
ata2: SATA max UDMA/133 cmd 0x3C88 ctl 0x3C82 bmdma 0x3C58 irq 19
ATA: abnormal status 0x7F on port 0x3C97
ata1: disabling port
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3f01 87:4003
88:203f
ata2: dev 0 ATA, max UDMA/100, 586072368 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi0 : ata_piix
scsi1 : ata_piix
Vendor: ATA Model: WDC WD3000JD-55K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 164k freed
Real Time Clock Driver v1.10f
Adding Swap: 1012052k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,8), internal journal
Intel 810 + AC97 Audio, version 1.01, 03:27:47 Sep 5 2005
PCI: Setting latency timer of device 00:1e.2 to 64
i810: Intel ICH4 found at IO 0x3880 and 0x3000, MEM 0xb0040800 and
0xb0040400, IRQ 17
i810: Intel ICH4 mmio at 0xe02ae800 and 0xe02b0400
i810_audio: Primary codec has ID 2
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 2
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not
present), total channels = 2
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb-uhci.c: $Revision: 1.275 $ time 03:28:47 Sep 5 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 23
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x38c0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x38e0, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0x3c00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: PCI device 8086:265c (Intel Corp.)
ehci_hcd 00:1d.7: irq 23, pci mem e0314000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: USB disconnect on device 00:1d.0-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: connect-debounce failed, port 1 disabled
hub.c: cannot disable port 1 of hub 1 (err = -19)
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: get_hub_status failed
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: get_hub_status failed
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 00:1d.1-0 address 1
usb.c: USB bus 2 deregistered
usb.c: USB disconnect on device 00:1d.2-0 address 1
usb.c: USB bus 3 deregistered
usb.c: USB disconnect on device 00:1d.3-0 address 1
usb.c: USB bus 4 deregistered
ehci_hcd 00:1d.7: remove state 3
usb.c: USB disconnect on device 00:1d.7-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: connect-debounce failed, port 1 disabled
hub.c: cannot disable port 1 of hub 1 (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: get_hub_status failed
usb.c: USB bus 5 deregistered
ohci1394: $Rev: 1045 $ Ben Collins
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[b0201000-b02017ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
ieee1394: Node removed: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
usb-uhci.c: $Revision: 1.275 $ time 03:28:47 Sep 5 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 23
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x38c0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x38e0, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0x3c00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: PCI device 8086:265c (Intel Corp.)
ehci_hcd 00:1d.7: irq 23, pci mem e0314000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
hid-core.c: USB HID support drivers
ohci1394: $Rev: 1045 $ Ben Collins
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[b0201000-b02017ff] Max
Packet=[2048]
Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension
(NICE) ver. 8.3.14 (11/2/05)
PCI: Setting latency timer of device 02:00.0 to 64
bcm5700 : Unknown NVRAM type.
VPD read failed
eth0: Broadcom BCM5751 1000Base-T PCI Express found at mem 4f800000, IRQ
16, node addr 000ae47ec497
eth0: Broadcom BCM5750 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON,
802.1Q VLAN ON, NAPI ON
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae4044833ea6e]
hub.c: connect-debounce failed, port 1 disabled
apm: BIOS not found.
hub.c: new USB device 00:1d.3-2, assigned address 2
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
Yenta ISA IRQ mask 0x04b8, PCI irq 23
Socket status: 30000006
Yenta ISA IRQ mask 0x04b8, PCI irq 20
Socket status: 30000006
lp: driver loaded but no devices found
usb_control/bulk_msg: timeout
input: USB HID v1.10 Device [Fujitsu Remote Control Receiver] on usb4:2.0
hub.c: new USB device 00:1d.0-1, assigned address 2
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb1:2.0
usb.c: registered new driver usbmouse
input: USB HID v1.10 Device [Fujitsu Remote Control Receiver] on usb4:2.1
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
hub.c: new USB device 00:1d.0-2, assigned address 3
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: new USB device 00:1d.0-2.1, assigned address 4
input: USB HID v1.00 Keyboard [Chicony PFU-65 USB Keyboard] on usb1:4.0
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 430M
agpgart: Detected an Intel(R) 915G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
cdrom: This disc doesn't have any tracks I recognize!

--
Kouzuma Kunikazu
kuni92@xxxxx


投稿者 xml-rpc : 2006年4月 6日 05:25
役に立ちました?:
過去のフィードバック 平均:(0) 総合:(0) 投票回数:(0)
本記事へのTrackback: http://hoop.euqset.org/blog/mt-tb2006.cgi/34468
トラックバック
コメント
コメントする




画像の中に見える文字を入力してください。