2009年7月23日

[plamo:29957] Re: linux-2.6.30.x

名倉@うちのほうでは雲が厚くて太陽の輪郭も見えなかった です。

> こじま@天気が一日ずれてれば日蝕も見えたのになぁ,,です.
>
> # まぁ,人生,そんなものだけど(苦笑
>
> From: 名倉昭一 <nagura-s@*********>
> Subject: [plamo:29955] linux-2.6.30.x

> Date: Thu, 23 Jul 2009 11:03:06 +0900
>
> > Full SCSIマシンでlibataベース起動不可あらっ でした。
>
> こういう報告こそ,ハードウェアの構成情報が必要なのでは?
>
> >   最もlibataベース得意なはずのFull SCSIなマシンlibataベースでは起動してくれない。
> >   まあintel 430VXな時代のマザーなので該当マシンは手元のみと思いますが。

430VX なマザー

root@xxxxx:/home/snagura# lspci
00:00.0 Host bridge: Intel Corporation 430VX - 82437VX TVX [Triton VX] (rev 02)
00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]
00:11.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 02)
00:12.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06)
00:13.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
00:14.0 SCSI storage controller: Adaptec AIC-7880U
root@xxxxx:/home/snagura# cat /proc/interrupts
CPU0
0: 24588 XT-PIC-XT timer
1: 8 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 1 XT-PIC-XT
4: 110 XT-PIC-XT serial
9: 1551 XT-PIC-XT aic7xxx
11: 498 XT-PIC-XT eth2
12: 61 XT-PIC-XT b43
14: 0 XT-PIC-XT ide0
15: 0 XT-PIC-XT ide1
NMI: 0 Non-maskable interrupts
ERR: 0

[ 2.976421] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.008236] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.031544] 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.053567] Uniform Multi-Platform E-IDE driver
[ 3.068917] piix 0000:00:07.1: IDE controller (0x8086:0x7010 rev 0x00)
[ 3.088889] piix 0000:00:07.1: not 100% native mode: will probe irqs later
[ 3.109809] ide0: BM-DMA at 0xf000-0xf007
[ 3.123136] ide1: BM-DMA at 0xf008-0xf00f
[ 3.136442] Probing IDE interface ide0...
[ 3.737207] Probing IDE interface ide1...
[ 4.337237] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.351234] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.368773] ide-gd driver 1.18
[ 4.384399] PCI: setting IRQ 9 as level-triggered
[ 4.384444] aic7xxx 0000:00:14.0: found PCI INT A -> IRQ 9
[ 19.426065] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 19.426089] <Adaptec aic7880 Ultra SCSI adapter>
[ 19.426107] aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
[ 19.426127]
[ 19.498457] scsi 2:0:0:0: Direct-Access COMPAQ ST32550W 6415 PQ: 0 ANSI: 2
[ 19.523033] scsi2:A:0:0: Tagged Queuing enabled. Depth 32
[ 19.539986] target2:0:0: Beginning Domain Validation
[ 19.565295] target2:0:0: wide asynchronous
[ 19.585389] target2:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
[ 19.612471] target2:0:0: Domain Validation skipping write tests
[ 19.630670] target2:0:0: Ending Domain Validation
[ 20.970851] scsi 2:0:6:0: CD-ROM MATSHITA CD-ROM CR-506 8S03 PQ: 0 ANSI: 2
[ 20.995597] target2:0:6: Beginning Domain Validation
[ 21.019031] target2:0:6: FAST-5 SCSI 5.0 MB/s ST (200 ns, offset 15)
[ 21.043588] target2:0:6: Domain Validation skipping write tests
[ 21.061761] target2:0:6: Ending Domain Validation
[ 23.189688] Driver 'sd' needs updating - please use bus_type methods
[ 23.215049] target2:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
[ 23.240758] sd 2:0:0:0: [sda] 4110000 512-byte hardware sectors: (2.10 GB/1.95 GiB)
[ 23.267429] sd 2:0:0:0: [sda] Write Protect is off
[ 23.282186] sd 2:0:0:0: [sda] Mode Sense: af 00 10 08
[ 23.286944] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 23.315590] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 23.333112] PNP: PS/2 appears to have AUX port disabled, if this is incorrect

>
> >   同じくFull SCSIのSocket3なマザーも同様でした。
> >   いずれもlinux-2.6.30.2ではATAドライバー組み込むことにより起動しています。

 Socket3 なマザー 

root@xxxxx:/home/snagura# lspci
00:05.0 Host bridge: Silicon Integrated Systems [SiS] 85C496 (rev 31)
00:0a.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
00:0b.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871
00:0c.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (rev 54)
root@xxxxx:/home/snagura# cat /proc/interrupts
CPU0
0: 481562 XT-PIC-XT timer
1: 8 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 1 XT-PIC-XT
4: 2 XT-PIC-XT
5: 4697 XT-PIC-XT eth1
9: 8089 XT-PIC-XT eth0
12: 3966 XT-PIC-XT aic7xxx
14: 0 XT-PIC-XT pata_isapnp
15: 0 XT-PIC-XT pata_isapnp
NMI: 0 Non-maskable interrupts
ERR: 0
[ 4.039856] 00:02: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 4.049879] Uniform Multi-Platform E-IDE driver
[ 4.069892] ide-gd driver 1.18
[ 19.180066] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 19.180066] <Adaptec 2940 SCSI adapter>
[ 19.180066] aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
[ 19.180066]
[ 19.197160] scsi 2:0:0:0: Direct-Access COMPAQ ST32550W 6416 PQ: 0 ANSI: 2
[ 19.197160] scsi2:A:0:0: Tagged Queuing enabled. Depth 32
[ 19.197160] target2:0:0: Beginning Domain Validation
[ 19.211774] target2:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 19.219190] target2:0:0: Domain Validation skipping write tests
[ 19.219190] target2:0:0: Ending Domain Validation
[ 20.511136] scsi 2:0:6:0: CD-ROM YAMAHA CDR400t 1.0q PQ: 0 ANSI: 2
[ 20.511136] target2:0:6: Beginning Domain Validation
[ 20.527302] target2:0:6: Ending Domain Validation
[ 20.550131] Driver 'sd' needs updating - please use bus_type methods
[ 20.560124] sd 2:0:0:0: [sda] 4110000 512-byte hardware sectors: (2.10 GB/1.95 GiB)
[ 20.570460] sd 2:0:0:0: [sda] Write Protect is off
[ 20.570460] sd 2:0:0:0: [sda] Mode Sense: af 00 10 08
[ 20.580126] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 20.590144] scsi3 : pata_isapnp
[ 20.590144] ata1: PATA max PIO0 cmd 0x1f0 ctl 0x3f6 irq 14
[ 20.600133] sda:<6>scsi4 : pata_isapnp
[ 20.600133] ata2: PATA max PIO0 cmd 0x170 ctl 0x376 irq 15
[ 20.610140] sda1 sda2
[ 20.640111] sd 2:0:0:0: [sda] Attached SCSI disk
[ 20.650141] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 20.650141] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 20.660158] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 20.670136] mice: PS/2 mouse device common for all mice
[ 20.670136] cpuidle: using governor ladder
[ 20.670136] cpuidle: using governor menu
[ 20.690110] TCP cubic registered
[ 20.690110] NET: Registered protocol family 17
[ 20.720100] input: AT Translated Set 2 keyboard as /class/input/input0
[ 20.790091] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 20.870091] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 20.910092] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 20.950092] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 20.990093] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 21.070094] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
[ 25.610163] ata1.01: qc timeout (cmd 0xec)
[ 25.610163] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 35.610314] ata1.01: qc timeout (cmd 0xec)
[ 35.610314] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 65.610766] ata1.01: qc timeout (cmd 0xec)
[ 65.610766] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 70.610842] ata1.00: qc timeout (cmd 0xec)
[ 70.610842] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 80.610992] ata1.00: qc timeout (cmd 0xec)
[ 80.610992] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 110.611445] ata1.00: qc timeout (cmd 0xec)
[ 110.611445] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[ 110.821497] kjournald starting. Commit interval 5 seconds
[ 110.821497] EXT3-fs: mounted filesystem with writeback data mode.
[ 110.821497] VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
[ 110.821497] Freeing unused kernel memory: 268k freed
[ 130.901806] 8139too Fast Ethernet driver 0.9.28
[ 130.971785] eth0: RealTek RTL8139 at 0xe800, 00:10:b5:56:91:af, IRQ 9
[ 130.971785] eth0: Identified 8139 chip type 'RTL-8139B'
[ 138.201896] Console: switching to colour frame buffer device 80x30
[ 138.441892] fb0: S3 Trio64V+ on 0000:00:0c.0, 2 MB RAM, 60 MHz MCLK
[ 139.361928] input: PC Speaker as /class/input/input1
[ 141.781970] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 141.781970] scsi 2:0:6:0: Attached scsi generic sg1 type 5
[ 142.101968] Driver 'sr' needs updating - please use bus_type methods
[ 142.181976] sr0: scsi3-mmc drive: 6x/6x writer xa/form2 cdda tray
[ 142.197776] Uniform CD-ROM driver Revision: 3.20
[ 142.261989] sr 2:0:6:0: Attached scsi CD-ROM sr0
[ 147.782038] Adding 200772k swap on /dev/sda1. Priority:-1 extents:1 across:2

>
> 使っている人には 430VX とか Socket3 だけでどういう SCSI チップを使って
> いるのかが分かるのかも知れないけど,私には分からないので,ドライバオプ
> ションとかも調べようが無いです.

 SiS730S な ECS K7SEM + adaptec AHA2940UW では異常ありませんでした。

>
> --------
> こじま
>

投稿者 xml-rpc : 2009年7月23日 13:55
役に立ちました?:
過去のフィードバック 平均:(0) 総合:(0) 投票回数:(0)
本記事へのTrackback: http://hoop.euqset.org/blog/mt-tb2006.cgi/86901
トラックバック
コメント
コメントする




画像の中に見える文字を入力してください。