2012年6月12日

Re: BBDB Horking Up Subject Header

At Mon, 11 Jun 2012 12:47:39 -0500,
andr辿s ram鱈rez wrote:
>
> Hi Ken.
>
> This is All the setup I have on my dot_wl file
> (define-key wl-draft-mode-map (kbd "<C-tab>") 'bbdb-complete-name)
>

> And bbdb works without any issue. My bbdb version is 3.02
>
> Regards.
>
> This is the content of my another configuration file (emacs-rc-bbdb.el)
> (require 'bbdb-loaddefs "~/.emacs.d/el-get/bbdb/lisp/bbdb-loaddefs.el");; version 3 and later (no autoloads)
>
> (setq bbdb-file "~/.emacs.d/bbdb") ;; keep ~/ clean; set before loading
> (require 'bbdb)
> (bbdb-initialize)
> (setq
> bbdb-offer-save 1 ;; 1 means save-without-asking
>
>
> bbdb-use-pop-up t ;; allow popups for addresses
> bbdb-electric-p t ;; be disposable with SPC
> bbdb-popup-target-lines 1 ;; very small
>
> bbdb-dwim-net-address-allow-redundancy t ;; always use full name
> bbdb-quiet-about-name-mismatches 2 ;; show name-mismatches 2 secs
>
> bbdb-always-add-address t ;; add new addresses to existing...
> ;; ...contacts automatically
> bbdb-canonicalize-redundant-nets-p t ;; x@xxxxx => x@xxxxx
>
> bbdb-completion-type nil ;; complete on anything
>
> bbdb-complete-name-allow-cycling t ;; cycle through matches
> ;; this only works partially
>
> bbbd-message-caching-enabled t ;; be fast
> bbdb-use-alternate-names t ;; use AKA
>
>
> bbdb-elided-display t ;; single-line addresses
>
> ;; auto-create addresses from mail
> bbdb/mail-auto-create-p 'bbdb-ignore-some-messages-hook
> bbdb-ignore-some-messages-alist ;; don't ask about fake addresses
> ;; NOTE: there can be only one entry per header (such as To, From)
> ;; http://flex.ee.uec.ac.jp/texi/bbdb/bbdb_11.html
>
> '(( "From" . "no.?reply\\|DAEMON\\|daemon\\|facebookmail\\|twitter"))
> )
> ;; mail alias
> (add-hook 'mail-setup-hook 'bbdb-define-all-aliases)
> (add-hook 'message-setup-hook 'bbdb-define-all-aliases)
> At Mon, 11 Jun 2012 10:21:06 -0600,
> Ken Gunderson wrote:
> >
> > Hello Again:
> >
> > I finally got around to configuring wl to use bbdb and all seemed well
> > (other than bbdb and flspell both competing for ESC TAB keybinding -
> > flyspell won) until I tried sending mail to recipient with multiple
> > "net" entries, whereupon selection of desired address resulted not
> > only in that address being inserted into "To:" field but also chomping
> > into "Subject:" header field in the draft buffer. This occurs to
> > various degrees depending upon how long the "net" address is,
> > e.g. maybe only leaving the "t" or maybe leaving "ject".
> >
> > Nothing special bbdb related in my .emacs:
> >
> > (require 'bbdb)
> > (bbdb-initialize)
> >
> > Nor my .wl:
> >
> > (require 'bbdb-wl)
> > (bbdb-wl-setup)
> > (setq bbdb-use-pop-up nil)
> > (setq bbdb/mail-auto-create-p nil)
> > (setq wl-summary-from-function 'bbdb-wl-from-func)
> >
> > Is this a known wl issue or something insidious....???
> >
> > Regards-- Ken

Thanks for the remapping bit. I tried using just that and minimal
bbdb lines in .emacs and results were the same. I am using
draft-config-alist to handle multiple imap accounts and though that
might be part of it but commenting out that code results in no
change. Subsequently, I also tried configuring a minimal .wl
containing _only_ the C-Tab mapping code and .... results were still
the same.

I seem to be encountering quite a few glitches using Wanderlust, which
I hope to resolve before I have to switch to something else. I'm on a
fairly up to date Archlinux box, Emacs 23.4, Wanderlust installed via
pacman labeled as version: 20120529-1, but start up splash bitmap says
"Almost Unreal", 2.15.9.

Other related packages:

emacs-apel v. 10.8-2
semi v. 1.14.6-3
flim v. 1.14.9-3
bbdb v. 2.35-5

Thanks again-- Ken


投稿者 xml-rpc : 2012年6月12日 04:29
役に立ちました?:
過去のフィードバック 平均:(0) 総合:(0) 投票回数:(0)
本記事へのTrackback: http://hoop.euqset.org/blog/mt-tb2006.cgi/110936
トラックバック
コメント
コメントする




画像の中に見える文字を入力してください。